TeraGel
Ž
(T-200) Blue & AgroGel
Ž
(T-400) Blue
There are three important variables that are involved in the
application of a super absorbent polymer such as TeraGelŽ (T-200) BlueŽ. First, is the
crystal size for the prevailing soil condition. TeraGelŽ (T-200)
BlueŽ is
produced in three different particle sizes: TeraGelŽ (T-200) BlueŽ HG, a small
crystal size used for shallow root zones, flower beds, small container
plants, hanging baskets. TeraGelŽ (T-200) BlueŽ LL are larger crystals available
for compacted, harder soil, deeper root zones or earth with little top
soil; (TeraGelŽ (T-200) BlueŽ RD) a minute particle size under 60-200 microns,
primarily used as a root dip that significantly reduces transplant shock
during the transfer of plants and trees, as well as providing a medium
for seed germination or in the transporting of plants and trees.
The AgraGelŽ (T-400) Blue™
crystal formulation has been specifically engineered
for agricultural use. Among its features include 100% acrylamide free
resulting in a zero tolerance
toxicity level and a wide variety of crystal sizes that promote maximum
absorbency while increasing aeration and drainage. AgraGel
Ž
(T-400) F is a smaller crystal size is approximately 200 microns and is
primarily used in extremely sandy soil. AgraGel
Ž
(T-400) Micro has been developed for use on a variety of grain crops and
is less than 100 microns in size.
The second variable is the depth of application
of the super absorbent for the root systems of the plants in question.
Since the feeder rutiles in the root zone of most plants seek out
moisture at depths of two to eight inches (2"- 8"), TeraGelŽ
(T-200) BlueŽ should be
installed in this band range contingent on the particular root systems
in question. As an example, for grass it should be placed at two to four
inches For laying sod on top of soil, spread and till only the top two
inches. In agricultural, landscaping and horticultural applications the
crystals are always installed into the prospective root zone.
For established grass, plants and trees, see our
TeraFloŽ liquid polymer product.
The third variable is the quantity of application.
Soil conditions such as salinity, pH of the soil, degree of
sand, climate, as well as the crop or plant in question, are all factors
in determining the quantity to be used. In extreme hot or dry climate
conditions or with use in porous sandy soils approximately twenty-five
to fifty percent (25%-50%) more TeraGelŽ (T-200) BlueŽ crystals should be used. In
broadcast applications, dependent on crop and prevailing conditions, per acre
quantities will range from as little as fifteen pounds to
twenty pounds for short rooted plants (vegetables) to thirty to thirty
five pounds for long rooted plants (alfalfa) to two hundred and fifteen
pounds per acre for grass & turf..
Remember, a little goes a long way and once TeraGelŽ
(T-200) BlueŽ
crystals are installed they will remain 95% actively effective after
seven to ten years!
TeraGel Ž (T-200) Blue
|
Containerized Plants &
Trees TeraGelŽ (T-200)
BlueŽ HG or
TeraGelŽ (T-200) BlueŽ LL |
| Size |
TeraGelŽ (T-200) BlueŽ HG |
|
Size |
TeraGelŽ (T-200) BlueŽ
(LL) |
|
Size |
TeraGelŽ (T-200) BlueŽ
(LL) |
|
Size |
TeraGelŽ (T-200) BlueŽ
(LL) |
| 4"- 6" |
˝ tsp |
1 gallon
|
a
oz. |
15 gallon |
3 oz. |
50 gallon |
8 oz. |
| 6"- 8" |
1 tsp
|
2 gallon |
˝ oz. |
20 gallon |
4 oz. |
100 gallon
|
12 oz. |
| 10"-12" |
2 tsp |
3 gallon |
ž oz. |
25
gallon |
5 oz. |
|
|
| 12"-14" |
3 tsp |
5 gallon |
1 oz. |
30
gallon |
6 oz. |
|
|
| 18"-20" |
4 tsp
|
10 gallon |
2 oz.
|
35 gallon |
7oz.
|
|
|
Greenhouse/Nursery usage:
For use as a soil amendment, thoroughly mix two pounds of
TeraGelŽ (T-200) BlueŽ
TeraGelŽ (T-200) BlueŽ HG or TeraGelŽ (T-200) BlueŽ LL per cubic yard or 1.2 oz. per cubic foot of soil.
Based on this volume of usage the following table can be used as a
general guideline; actual pot dimension may vary slightly. For sandier
soils increase quantity by 33% to 3 lbs./ cubic yard. At an approximate
cost of $3.00/lb., the following table provides the added cost per
container for the addition of TeraGelŽ (T-200) BlueŽ crystals. .
| Cont. size |
Qty/cu.yd.
|
Cost/plant |
|
Cont. size |
Qty/cu.yd. |
Cost/plant |
| 2 1/2" round |
5,616
|
$0.0005 |
8" round |
186 |
$0.016 |
| 2 1/2" square |
6,048 |
0.0005 |
12" round |
162 |
0.018
|
| 4" round |
1,296 |
0.002 |
1 gallon |
142 |
0.021 |
| 4" square |
1,512 |
0.002 |
3 gallon |
122 |
0.025 |
| 5" round |
756 |
0.004 |
5 gallon |
50 |
0.060
|
| 6" round |
432
|
0.007 |
11" x 2.25" x
2 1/4" |
1124 |
0.024 |
|
TeraGelŽ (T-200)
BlueŽ HG or TeraGelŽ (T-200) BlueŽ LL
- Applications |
|
Boxed Trees |
Ball & Burlap
(B & B) |
|
Container |
Quantity |
|
Tree Diam. |
Tree Height |
Qty. |
|
Tree Diam. |
Tree Height |
Qty.
|
|
24" |
6
oz. |
1"
caliper- |
3'
height |
2
oz. |
5"
caliper- |
14-
16' ht |
12
oz. |
|
30" |
9
oz. |
2"
caliper- |
8-10' ht |
3
oz. |
6"
caliper - |
16
-18' ht |
16
oz. |
|
36" |
12
oz |
3"
caliper |
10-12' ht |
6
oz. |
7"
caliper - |
18
-20' ht |
20
oz. |
|
48" |
16
oz. |
4"
caliper |
12-14' ht |
8
oz. |
8" caliper - |
20
-22' ht |
24
oz. |
Mix 1/2
TeraGelŽ (T-200) BlueŽ throughout planting hole and amend back fill
with remaining 1/2.
TIP: If planting in clay or hardened soil incorporate TeraGelŽ
(T-200) BlueŽ LL
in upper 1/3 of hole to decompact soil.
|
Planting
Beds: TeraGelŽ (T-200) BlueŽ HG |
Rate
|
|
|
Rate |
| 1 sq. ft. (1"
depth) |
1˝ tsp
|
100 sq. ft.
(1" depth) |
1 lb.
|
| 1 sq. ft. (3"
depth) |
2 tbsp
|
100 sq. ft.
(3" depth) |
3 lb. |
| 1 sq. ft. (6"
depth) |
3 tbsp |
100 sq. ft.
(6" depth) |
6 lb. |
Mix thoroughly throughout planting area to the required depth.
|
Containerized Plants &
Trees TeraGelŽ (T-200) BlueŽ HG or TeraGelŽ (T-200) BlueŽ LL |
|
Size |
TeraGelŽ (T-200) BlueŽ HG |
|
Size |
TeraGelŽ (T-200)
BlueŽ LL |
|
Size |
TeraGelŽ (T-200) BlueŽ LL |
|
Size |
TeraGelŽ (T-200) BlueŽ LL |
|
4"- 6" |
˝ tsp |
1 gallon
|
a
oz. |
15 gallon |
3 oz. |
50 gallon |
8 oz. |
|
6"- 8" |
1 tsp |
2 gallon |
˝ oz. |
20 gallon |
4 oz. |
100 gallon
|
12 oz. |
|
10"-12" |
2 tsp |
3 gallon |
ž oz. |
25
gallon |
5 oz. |
|
|
|
12"-14" |
3 tsp |
5 gallon |
1 oz. |
30
gallon |
6 oz. |
|
|
|
18"-20" |
4 tsp |
10 gallon |
2 oz. |
35 gallon |
7oz.
|
|
|
Mix thoroughly and blend into media following rates
listed; insert plant into soil, cover and water liberally.
For established plants, Either completely re-pot the
plant or remove soil down to the root zone and mix the recommended
amount with soil. Replace soil and water liberally to activate the
crystals. The greater the dispersion of the crystals , the better.
|
Lawns & Sod
TeraGelŽ (T-200)
BlueŽ LL |
|
Area |
Quantity |
|
Area |
Quantity |
| 1 sq.ft. (2" depth)
|
0.50 tsp
|
1000 sq.ft. (2" depth)
|
5
lbs. |
| 100 sq.ft. (2" depth) |
25 tbsp
|
1 Acre (2" depth)
|
215
lbs. |
| 200 sq.ft. (2" depth) |
1 lb. |
|
|
Application rates are at five pounds per 1000 sq. ft.
per two inch depth or 215 lbs per acre. Watering schedules can be
extended 3 days for each five pounds of TeraGelŽ (T-200) BlueŽ crystals installed per
two inch depth up to a maximum of 15 pounds per 1000 sq.ft...
For sandy soil conditions, increase quantity by 33%
to 50% dependent on the degree of sand in the soil.
For seeding: Spread with a drop seeder or spreader,
till into the top 2" to 4" of soil then spread seed, roll and water
liberally to activate the polymer.
For sod: Disperse
TeraGelŽ (T-200) BlueŽ evenly on
top of soil and work into the top 2" to 3". Prior to laying sod, disperse evenly
an additional one pound on
top of the soil to create immediate adhesion of the thatch layer..
Install the sod sections and water
liberally. Fertilizers and other water soluble additives may be added at
the time of installation.
Note: For already established grass, see our TeraFloŽ TG, liquid polymer
.
|
Bare Root Transplants & Plugs
(TeraGelŽ (T-200) BlueŽ RD or TeraGelŽ (T-200) BlueŽ HG) |
|
Quantities |
|
Quantities |
| 1 cup water
|
1/4 tsp
crystals |
1 gallon
water |
4 tsp
crystals |
| 1 quart water |
1 tsp
crystals |
35-50 gallons
water |
1 pound
crystals |
Combine TeraGelŽ (T-200) BlueŽ crystals and warm water to make a
pasty gravy-like mixture. Let stand for 45 minutes and adjust thickness
to ensure that the crystals adhere to the bare roots. Other water
soluble additives can now be added to the slurry mix. Dip roots into
hydrated mixture and plant seedling into amended soil by incorporating
dry crystals TeraGelŽ (T-200) BlueŽ HG into backfill and hole and then plant. One pound of
TeraGelŽ (T-200) BlueŽ will provide root dip treatment for approximately 12,000-15,000
plants. In field conditions, apply approximately 1 ˝ -2 oz. of hydrated
gel per seedling plant and cover over with soil.
TIP: Add rooting hormones or fertilizers to
hydrated mix to give plants a great jump start! Pesticides, herbicides
and insecticides can also be added to the hydrated mixture for their
specific added benefits including elimination of air borne toxicity.
Tree Transplanting: TeraGelŽ (T-200) BlueŽ LL
Application rate of approximately one ounce of
TeraGelŽ (T-200) BlueŽ per one foot diameter of root ball. Mix 1/2 throughout the
planting hole; mix remaining 1/2 with back fill. Do not amend top two
inches of back fill. Water liberally to activate polymer. Rate should be
increased by 50% per foot of root ball for very sandy soils. ˝ oz. / 4"-
6" root ball; 1 oz ./8" - 12" root ball.
Bulk Soil Amendment TeraGelŽ
(T-200) BlueŽ HG or
TeraGelŽ (T-200) BlueŽ LL
Mix 2 lbs/cubic yard or 1.2 oz./cubic foot. For sandy
or porous soil, increase quantity by 50%.
Note: 100 sq. ft. with a depth of six
inches is equal to 50 cubic feet of soil.
|
Soil Volumes |
| 25.7 quarts =1
cubic foot |
|
28 liters = 1
cubic foot |
| 27 cubic feet =
1 cubic yard |
|
22 bushels = 1 cubic
yard |
Transporting of Trees/Shrubs/Plants
(TeraGelŽ (T-200) BlueŽ RD) or TeraGelŽ (T-200) BlueŽ HG
Dip smaller root balls into hydrated
TeraGelŽ (T-200) BlueŽ mixture
along with all appropriate additives prior to applying burlap cover.
With larger trees and shrubs spray onto root ball, apply burlap and
water.
Seed Germination (TeraGelŽ
(T-200) BlueŽ RD)
Thoroughly mix one-half pound
TeraGelŽ (T-200) BlueŽ (TeraGelŽ (T-200) BlueŽ RD) with
each 50 lbs. of seed prior to planting.
Alternative method: Using transplant mixture of one
pound of TeraGelŽ (T-200) BlueŽ with 25 gallons of warm water, place seeds into
mixture and cover slightly with hydrated mix. For best results after
germination, place seedlings into TeraGelŽ (T-200) BlueŽ amended soil.
AgraGelŽ (T-400) Blue™ AG
CROP GROWERS
Broadcast planting:
Amounts can range from 15 to thirty five (15 lbs -35
lbs.) pounds per acre dependent on crop and soil condition. Specific
crop use information is available upon request. Dispersing the TeraGelŽ
(T-200) BlueŽ
crystals is performed with a drop seeder or spreader which throws the
crystals in an even pattern over the intended growth area. In
poorer economic situations, disperse evenly, by hand if necessary, with
the use of a hand spreader.
After all the other ingredients are added, the soil
is then tilled under to the required potential feeder root depth and
then substantially irrigated at the initial watering to activate the
polymer or wait for rain.
A watering schedule can now be established by
extending the days between watering. The new watering schedule should
begin by adding one day to the normal watering cycle. Continue adding an
additional day between irrigations until the new cycle is determined.
Extending the watering cycle twice the previous schedule is not
uncommon. Since rapid absorption is another feature of the TeraGelŽ
(T-200) BlueŽ
polymer, (brief and lengthy) rainfalls may be added to the irrigation
cycle. Use of a simple hydrometer or tensiometer to measure moisture in
the root zone is a useful tool since subsurface moisture cannot be
easily observed.
Row or band installation: (AgraGelŽ (T-400)
Blue™ AG)
Dependent on crop, climate, soil condition, and
method of application, rates can vary from three to eight pounds (3 lbs
to 8 lbs) per acre. Installation can be performed using and insecticide
box. Fertilizers and other water soluble additives can be applied along
with the crystals. Replace soil and irrigate to activate the crystals.
For smaller gardens, a "pinch" of crystals is placed into the seed slot
along with a starter fertilizer and the seed or seedling and
covered over with soil. Water liberally to activate the crystals.
More accurate rates of application can be performed
by hydrating the crystals first and then applying the exact amount by
weight into the seed slot, usually 2 oz. per plant. In using row or band
planting, the plant and soil placement varies from season to season
therefore additional applications of TeraGelŽ (T-200) BlueŽ are required the following
year.
In the case of seedlings, they can be dipped into a
hydrated gel (slurry) containing all the other necessary additives for
that particular plant. These additives are added to the mixture after
hydration and given an opportunity to be absorbed.
This gel mixture can also be applied with a large
water tanker and should require no more than a 1/2" diameter nozzle for
application. A pre-set amount is then dispersed down the rows at a rate
of 2 oz per seedling. Setting up irrigation schedules should be followed
as previously stated for broadcast planting.
For detailed information on rates or methods for
specific crops call 1-888-383-7293.
TeraFloŽ - TG (Turf Grass formula)
Rates for TeraFloŽ Liquid Polymer
|
As a Wetting Agent: |
|
6 oz. per 1000 sq. ft. |
| As a Soil
Penetrant |
(1) gallon
per acre - sprayed |
| Monthly
maintenance |
64 oz. per
acre per month |
| As an
Adjuvant |
5 to 10 oz.
per 100 gallons |
| Complete
Moisture Management |
2 to 4
gallons per acre per month |
|
The product must be agitated for thorough mixing. Irrigate lightly immediately after application to
allow product access to the root zone. A 40:1 water to product mixture will ensure proper
distribution when spraying or in irrigation systems. When used as a lubricant in high pressure and liquid
injections systems the ratio of water to product is 150:1
|
TeraFloŽ
- HC (Horticultural formula)
|
As a Root dip: |
|
˝ oz. per gallon of water |
|
As a Drench (Plants in production): |
4 oz. mixed with (1) gallon of water |
|
As a Drench
(Plug-First Leaf) |
ź oz. per gallon of water |
|
Pre-shipment Drench: |
˝ oz. per gallon of water |
|
For nitrate retention: |
1ź oz per gallon of water |
|
Injection irrigation: |
200 ppm weekly / 20 ppm daily |
|
Soil-less Growers Mix: |
10 oz. mixed with water to evenly spray one (1) cubic
yard of mix
Note: Rates may be increased or decreased due to the
variations in grower’s formulation of soil mix. |
|
ALL TeraFloŽ
formulas must be mixed thoroughly before
use.
Once mixed it will remain in suspension. |
TeraFloŽ LS (Landscape formula)
Turf grass
Spray Surface : 1 gallon per (10,000 sq ft)
Thoroughly mix 40 :1 with water, 4 gallons
/acre
Sod (Prior to or post application)
Thoroughly mix 40 :1 with water, 4 gallons
/acre
Trees
Trees & shrubs (Planting)
3 oz per inch of root ball, Mix 30
: 1 with water and drench root ball and hole
Trees & shrubs (Established)
Use 6 oz per inch of trunk diameter, 40 : 1 for the first application.
Thereafter, use 3 oz. per inch of trunk diameter every six weeks.
A 40:1 water to TeraFloŽ mixture will
ensure proper distribution when spraying or when used in irrigation/fertigation systems.
Root Dip & plants
6 oz per gallon of water. Dip roots and plant as
normal.
Always irrigate lightly immediately after application to
allow product access to the root zone
TeraFlo AG™
Recommended rate is one to four gallons (1-4 gallons) per acre
depending on conditions, however, the optimal application rate for any
given field may vary depending on intended use, soil factors and row
conditions.
Broadcast application:
Spray on surface immediately after planting at a rate
of four (4) gallons per acre.
Rate may vary from (2) to (4) gallons per acre
contingent on soil type, field conditions and desired benefits.
Direct Furrow Application:
Method #1 The application can be performed with drip irrigation
or overhead sprinklers.
| Furrow
length (ft)
|
44" furrow
|
60" furrow |
| 200 |
8.5 oz
|
11.75 oz |
| 400 |
17.0 oz |
23.50 oz |
| 600 |
26.0 oz |
35.00 oz |
| 800 |
34.5 oz |
47.00 oz |
| 1000 |
43.5 oz |
60.00 oz
|
| 1200 |
52.0 oz |
71.00 oz |
| 1400 |
60.5 oz |
82.50 oz |
| 1600 |
70.0 oz |
94.00 oz
|
Method #2 AgroFlo™
can be applied directly into pipe flow (fertigation)
or head ditch (flood irrigation).
|
Flow Rate |
Application Rate |
| Gallons
/ min
|
Ounces / minute |
| 100 |
3.2 |
| 200 |
9.6 |
| 300 |
13.0 |
| 400 |
16.0 |
| 500 |
22.5 |
| 600 |
26.5 |
| 700 |
28.8 |
| 800 |
35.0 |
| 900 |
38.5 |
| 1000 |
41.6 |
| 1100 |
48.0 |
As a surface sealant for improved crop emergence:
Apply 192 oz.per acre diluted with minimum 50 gallons of water for
improved crop emergence, rapid plant establishment and prevention of
soil moisture release to the atmosphere
As a penetrant: Mix 500:1
As a moisture barrier:
Mix 200:1 as a root moisture barrier to prevent nitrogen loss
Salt
Out
™
Treatment Program:
Initial applications: Apply 4 gallons per
acre or 12 fl oz per 1000 ft˛.
Reapply at 6-8 fl oz per 1000 ft˛ every two weeks until
plant conditions improve.
Maintenance use: Apply 6 -8 fl oz per 1000 ft˛ monthly.
A light syringe (1/8") of water after each application is
required.
Salt-Out!™ can be applied through irrigation and fertigation
systems.
Tank mixing instructions:
Gradually add Salt-Out!™ to the mixing
tank while filling. Make sure that the mixture is thoroughly
agitated to provide uniform dispersion throughout. For
sprayer tank use, mix Salt-Out!™ at a minimum ratio of 1
part Salt-Out!™ to 40 parts of water.
Once Salt-Out!™ is in
suspension it will remain in suspension.
Available in 5 gallon containers 30 gallon drums and 55
gallon drums
Total Turf
™
General Application:
Can be applied by boom sprayer, hose end applicator, drip irrigation,
injection, or fertigation system. It is a cost effective concentrate and
must be thoroughly agitated and mixed 30 parts water to 1 part product.
Turf grass:
Mix 8 to 12 fl. oz. in 2 gallons of water per 1000 sq. ft. monthly.
Apply at the 12 fl. oz. rate for rapid improvement of turf under high
stress discoloration. Apply just prior to fertilizer application.
Lightly irrigate immediately after application to allow access to the
root zone.
Indoor Plant:
Apply at the base of the plant using a mix of 10 parts water to 1
part product.
Do not apply
directly on petals of flowering plants.
Petals will turn brown and fall off.
Active Ingredients: Liquid acrylamide copolymer, humecants,
sulfates, and proprietary additives - 50% by weight.
Inert Ingredients -50% by weight.
Precautionary Statements: Non hazardous to humans, animals and
fish. No known environmental hazards.
Airex DC™ Drift Control
Application Rates:
ź % to 2%
by volume of Airex DC™ per gallon of spray mixture.
Agitate mixture thoroughly prior to use.
By irrigating immediately after an application, Airex DC™
becomes a penetrant that enhances the uptake of selective and
non-selective components through the cuticle layer of the target
species, or by penetrating compacted surface layers of the soil in
target root zones.
Final Step (TeraGelŽ (T-200) BlueŽ LL)
6 oz. bag - coverage rate 32 sq. ft.
Evenly disperse
4 oz. into top 2 inches of the soil. Disperse balance (2
oz.) on soil surface. Replace the sod and irrigate to activate the
crystals.
